A Step-by-Step Guide to Setting Up a Bath Tub
A Step-by-Step Guide to Setting Up a Bath Tub
Blog Article
We've noticed this great article relating to How to Install a Bathtub listed below on the net and figured it made good sense to discuss it with you on this site.
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bath tub with a new one is also a moderately tough task. If the old bathtub is easily obtainable, the task can move rapidly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. Make sure you have qualified on your own for the work and also are comfortable attempting it. As opposed to working with a professional to take control of a halfway-completed job, it is far better to consider employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This article will assist you set up a brand-new bath tub in your bathroom if you have already purchased a new tub as well as do not require to transform the setup of your previous water supply pipes.
Your tools and material checklist ought to make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing taps can be quite bothersome as a result of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the staying water that will certainly come from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. Once the faucets have been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in area in between the faucet and the sink. Safeguard the faucet in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap ports. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using both wooden boards under its feet, put the bathtub in the needed position. The wooden boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit the bottom of the furthest adaptable faucet port to the proper supply pipe by making a compression join; after that do the same for the other faucet.
Activate the supply of water as well as examine all joints and brand-new pipework for leakages and tighten them if required. Load the bath tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has actually been made use of at least once as this will resolve it right into its last position.
Preparing for the Installation
First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the adaptable faucet ports to the bottom of both taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its last setting.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly load the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can fracture relatively early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very taken with How to Install a Bathtub and I'm hoping you enjoyed reading the new blog entry. Those who liked our blog posting plz be sure to share it. I praise you for your time. Kindly come by our website back soon.
Estimate Free
Report this page